4. The lowest BSFC values were obtained with 30% methanol and 70% diesel fuel. The exhaust temperature for diesel fuel was higher compared to any mixing of the blended fuel. Methanol-Diesel MD engine • Methanol is burnt according to diesel process • Methanol is injected close to TDC and ignited by a small amount of diesel pilot fuel Pros Cons + no knocking (diesel combustion) + no power reduction + good load acceptance + cost effective adaption + low THC, CO (and formaldehyde) levels + good back-up fuel performance The proposed concept utilizes a high-temperature combustion system-enabled by a combination of thermal insulation, reduced turbocharger aftercooling, and exhaust gas retention-to combust low-cetane “sootless” fuels like ethanol, methanol, and natural gas in a traditional Diesel-style combustion mode (i.e. Zhu research showed that mixing methanol and biodiesel with diesel fuel reduces the ash content. When I make my fuel I pour 1 litre of oil in a 5 litre can then top it up with 4 litres of methanol. The proposed concept utilizes a high-temperature combustion system-enabled by a combination of thermal insulation, reduced turbocharger aftercooling, and exhaust gas retention-to combust low-cetane “sootless” fuels like ethanol, methanol, and natural gas in a traditional Diesel-style combustion mode (i.e. Switching to and from Emission Control Area (ECA)-compliant fuels when entering or leaving an ECA poses a range of issues for vessel operators. China invests in methanol In 2009 the Standardisation Administration of China, the central government body responsible for industry standards, issued regulations for methanol fuel (covering 100% methanol and an 85:15 mix of methanol and diesel, known as M85), giving methanol vehicles legal status. For those unfamiliar with the hydrometer, it is a simple device which uses a calibrated weight to float in the fluid to be checked, the level at which the float sits in the fuel indicating the specific gravity of the fuel.
Compatibility challenges have always been present when mixing heavy fuel oils (HFO), and the growth of environmental legislation has made it even more important to be aware of fuel compatibility issues.

Biodiesel is an alternative fuel for diesel engines made from vegetable oil and/or animal fat. The BSFC for diesel fuel was much lower compared to any mixing ratio. Experimental results showed that the output power and torque for diesel fuel is lower compared to methanol-diesel blended fuel at any ratio. The best mixing ratio that produced the lowest exhaust temperature was at 10% of methanol in 90% of diesel fuel. How to mix methanol and water correctly to target correct %? The low temperature limit of emulsions may be extended through adding antifreeze agents (e.g., methanol) to the formulation.

In order to develop the high revs of which it is capable the glo-engine must be fairly "sloppy", and to ensure adequate compression for starting a fairly oily viscous fuel is needed. Properties of emulsified fuels differ significantly from the properties of pure diesel fuel, resulting in numerous engine effects. mixing-limited diffusive combustion, rather than HCCI-like strategies).

The FuelMeister processor we used conveniently lets you do the methanol/lye mixing … Methanol does not have the natural inherent oiliness of diesel oil, and glofuels must have a higher oil content than diesel fuels. Heat your oil to 120 F, then add the calculated amount of methanol/hydroxide mixture. Impact on Combustion and Engine Performance. The best mixing ratio that produced the lowest exhaust temperature was at 10% of methanol in 90% of diesel fuel. That's a 4:1 mix or 20% oil and is a very good (safe) mix for just about any engine. The lower the ash content, the longer hard particle filters are not jammed, as ash is not produced in the process of combustion, and the exhaust emission control system is less loaded [28] , [29] . As we know water is 1, Methanol coming out at 0.79 and Nitromethane at 1.13, it is easy to establish the fuel mixture.
example a 10.55 : 1 ratio is a 10.55 ratio no mater what the fuel but that is not mean that any fuel at a 10.55:1 ratio will burn correctly .. with the correct mix of gas and methanol I can mimic the same a/f ratio of E85 and it be the correct ratio for the burn.. The exhaust temperature for diesel fuel was higher compared to any mixing of the blended fuel.

The mixing ratios of methanol to diesel were 0:100, 10:90, 20:80 and 30:70. Thousands are now "home brewing" fuel for their cars, at a tenth of the price at the pump. I've never bothered with nitro.

The lowest BSFC values were obtained with 30% methanol and 70% diesel fuel. The "DIY diesel" is tax free and costs just about 9p a litre to … Methanol was mixed at different ratios with diesel fuel. Since it is derived from renewable organic materials and has been shown to reduce certain harmful emissions when burned compared to conventional diesel, biodiesel has received wide attention as a "green" source of energy. Here are steps to synthesize this renewable fuel yourself.